FREE AUDIO TOOL / LOCAL FILE CHECK
Online WAV file inspector.
Sample rate, channels & peaks.
Check a WAV recording’s sample rate, channels, waveform, and digital levels. Your file stays on this device.
Privacy-first & local-only: Your selected WAV file is parsed directly on your device—audio bytes, filenames, and peak readings are never uploaded or retained by our server, and results clear when you press Clear or close the tab. No accounts or ads; cookieless site stats count only anonymous page visits and tool starts. Website privacy details →
Choose a WAV to inspect.
Uncompressed PCM or IEEE float WAV, up to 50 MiB and eight channels. Analysis runs locally; nothing plays automatically.
Enable JavaScript to inspect a WAV file locally.
Supports integer PCM at 8, 16, 24, or 32 bits and IEEE float at 32 or 64 bits, including compatible extensible WAV. Compressed WAV, RF64, and big-endian files need exporting as PCM first.
YOUR FILE / LOCAL RESULTS
Inside the recording.
Waveform overview
Each row represents a channel, in file order. The overview shows sample peaks, with zero at the center and ±1 at the edges; the table below provides a text equivalent. Channel numbers do not assume a speaker layout.
| Channel | Sample peak | RMS level | Near full scale samples |
|---|
Near full scale counts samples with magnitude ≥0.999 (about −0.009 dBFS), including float samples above 0 dBFS. This is a warning to inspect the recording, not proof of clipping. These are sample peaks, not reconstructed true peaks or LUFS loudness.
Quiet sections
A quiet section lasts at least 0.5 seconds with every channel below −60 dBFS sample peak, measured in roughly 0.1-second blocks. Short gaps may be missed. Digital silence counts frames where all channels are exactly zero.
What do the numbers mean?
Sample rate is the number of sample frames stored per second. This tool reads the original WAV header, without decoding through a browser audio output or changing the rate. A 44,100 Hz file remains 44,100 Hz here even if your sound device uses 48,000 Hz.
Channels tells you how many separate signals are in the file. If a stereo recording has one silent channel, check your input channel selection, cable, and routing. Compare left and right live playback with the headphone stereo test.
dBFS describes digital signal level relative to full scale. Zero dBFS is the reference limit for integer PCM; floating-point files can hold values above it. A silent channel shows −∞. These values do not measure room noise, headphone volume, or hearing.
RMS level summarizes signal energy across the whole file, including silence. A quiet recording or a few full-scale peaks cannot identify a hardware failure by themselves. Follow the microphone troubleshooting guide or crackling and popping checklist to isolate the cause.
Local analysis, useful limits.
The inspector reads only the file you select. Audio bytes and filenames are never sent to the server. Clear removes the results; leaving the page cancels unfinished work. Standard site analytics can count a completed inspection without the file’s contents or name.
This tool inspects stored samples. It does not listen for defects, repair files, verify your audio driver settings, or estimate network latency. For a recording made through MicDrop, the file describes the recorder’s output and may include processing or resampling applied before it was saved.
Common WAV file format & peak level questions
How do I check if a WAV file is 16-bit, 24-bit, or 32-bit float?
Select the file above and read the format summary directly from its RIFF/WAVE header. Unlike browser audio players that resample to your sound card’s rate, this inspector parses the raw header bytes locally to report exact bit depth, encoding, and sample rate.
What does 0 dBFS or near-full-scale peak mean in a WAV recording?
In integer PCM WAV files, 0 dBFS is the maximum sample ceiling—repeated samples at or near ±1.0 often indicate clipped input gain or a hard limiter. In 32-bit float WAVs, peaks above 0 dBFS can exist without permanent clipping until exported to integer formats.
Why is one channel silent in my stereo WAV recording?
A single XLR or mono microphone recorded onto a two-channel stereo track normally fills Channel 1 and leaves Channel 2 silent (−∞ dBFS). Switch your recorder or OBS source to mono—or enable mono downmix—so speech plays centered in both ears.
Why won’t a compressed WAV, RF64, or MP3 open in a PCM WAV inspector?
WAV is a container that can wrap ADPCM, MP3, or broadcast RF64 chunks over 4 GB. Export the clip as standard uncompressed 16-bit, 24-bit, or 32-bit float RIFF WAV (up to 50 MiB) to inspect raw sample peaks locally.