FREE AUDIO TOOL / PLAYBACK ONLY

Left & right audio test.
Check headphones & speakers.

Check headphone channels with tones and spoken labels. Compare a centered signal, stereo separation, mono playback, and polarity without granting microphone access.

Privacy-first & local-only: All tones and channel checks play locally in your browser—this tool requests no microphone access and never records, uploads, or retains anything on our server. No accounts or ads; cookieless site stats count only anonymous page visits and tool starts. Website privacy details →

Start with your device volume low.

Put on your headphones and choose one check. Playback uses your browser’s current output and stops automatically after a short clip.

Compare the same audio path

The stereo sample sends a lower tone left and a higher tone right. The mono sample mixes both tones equally into both channels. Each comparison lasts two seconds.

Applies to the center tone and comparison samples. Changing balance stops playback; play again to compare. Left/right labels always use their named channel.

Enable JavaScript to use the sound controls.

Signal percentage is not calibrated loudness. Stop also works with Escape. Playback stops when you leave or hide the page. No microphone access, recording, uploads, or account.

What should you hear?

Interpret the channel checks
ResultNext check
Left only on the left; right only on the rightThe current path preserves separation for this sample.
Either label or tone sounds in both earsCheck mono accessibility settings, mixer routing, and any voice-call profile. Keep mono enabled if you rely on it.
The sides are reversedCheck headphone orientation and channel swapping in the output path.
Center tone leans to one sideReset the comparison balance above, then check system balance, headphone fit, cable seating, and another audio source. This tool cannot diagnose hearing or hardware.
Stereo and mono sound equally centeredA mono mix may be occurring later in the path. Compare using wired headphones and check accessibility or communication-mode settings.
Opposite polarity becomes quiet or silentAt centered balance the signals are exact opposites, so summing them to mono cancels them. This is an intentional demonstration, not an automatic fault result. Do not raise the volume to chase the cancellation.
One side or both sides stay silentReseat the plug, test another source, or follow the Windows no-sound, Mac no-sound, or Bluetooth silent checklist.

Check the full MicDrop path

Open this test on the computer sending audio and route that browser’s output through MicDrop to your phone. Opening it on the phone tests the phone’s local browser output instead. Compare playback-only with your usual microphone mode to see whether channel behavior changes.

What this test tells you

The page sends known digital signals to your browser’s current output. Your operating system, headphones, Bluetooth profile, accessibility settings, and room can change what you hear. A phone speaker may not provide headphone-like separation. These checks do not measure hearing, frequency response, or latency, and the page cannot automatically know what you heard.

For a specific frequency or a longer sweep, use the tone and noise generator. To check an input, use the microphone test and recorder.

If sound is faint, check the Windows low-volume controls. If quality drops when a microphone opens, read why Bluetooth headphones change quality. If audio arrives late, use the audio-delay checklist and the audio sync check.

Common headphone & speaker channel questions

Why are my left and right headphone channels reversed?

Check the physical L and R markings on the earcups or detachable headphone cables first. On desktop speakers, verify the left/right RCA or 3.5 mm interconnect orientation, then inspect any equalizer, virtual surround, or audio-interface routing software that can swap output channels.

Why does the left or right stereo test play in both ears?

Your device or app is summing stereo audio to mono. Check Mono audio under Windows, macOS, iOS, or Android accessibility settings, or leave any active voice call that forces Bluetooth earbuds into a single-channel hands-free call profile.

Why is one side of my headphones quieter than the other?

Reset the comparison balance slider above, check your operating-system left/right output balance, and reseat any 3.5 mm or detachable earcup plug completely. Testing the same headphones on a second device separates a computer setting from earwax buildup, cable wear, or driver imbalance.

Can I test Bluetooth earbuds or desktop speakers without a microphone?

Yes. Every check on this page is playback-only and never requests microphone permission. Keeping the microphone closed also lets Bluetooth headphones stay in their normal stereo music profile instead of switching into lower-bandwidth call mode.